Klipper-Adaptive-Meshing-Purging (KAMP) incorporated

[bassamanator]

Printers

• Sovol SV06
• Sovol SV06 Skr-Mini-E3-V3.0
• Sovol SV06 Plus

Will push to all other branches after testing in develop is successful.

Changelog

• Imports in printer.cfg adjusted.
• KAMP can be enabled/disabled from within [gcode_macro _globals]; enabled by default only in this release/branch.
• Other minor code cleanup.

Installation

• Standard instructions in master README.md can be followed, however, relevant code lives in the develop branch, be sure to pull the correct branch.

---

This discussion was created from the release Klipper-Adaptive-Meshing-Purging (KAMP) incorporated.

[Manfredo1952]

Good day - how's the progress re testing this with the SV06 and possible transfer to SV06+, please ?

[bassamanator]

KAMP is working fine on my end, no reports from other users. It's really not an issue, you can easily disable it via the _globals marcro/section. If you're comfortable with these things, feel free to pull all code from develop branch, except for the printer.cfg which you should use from either the sv06-plus branch, or use your existing printer.cfg.

In any case, I'll be merging KAMP into all branches at some point this week.

[Carpenter64]

Hi, I use it on SV06+ since I saw you were including it in the SV06 branch a few days ago. It's working great. I really like it ! Great idea to include it in all branches. Have a nice day ! Le lun. 24 juil. 2023 à 07:01, Bassam ***@***.***> a écrit :

…

KAMP is working fine on my end, no reports from other users. It's really not an issue, you can easily disable it via the _globals marcro/section. If you're comfortable with these things, feel free to pull all code from develop branch, except for the printer.cfg which you should use from either the sv06-plus branch, or use your existing printer.cfg. In any case, I'll be merging KAMP into all branches at some point this week. — Reply to this email directly, view it on GitHub <#75 (reply in thread)>, or unsubscribe <https://github.com/notifications/unsubscribe-auth/A5VUC3NU2YUNCJEGMHQCIJ3XRX6SBANCNFSM6AAAAAA2BMZUXU> . You are receiving this because you are subscribed to this thread.Message ID: <bassamanator/Sovol-SV06-firmware/repo-discussions/75/comments/6524719 @github.com>

[bassamanator]

Thanks for the feedback!

[chrisngobanh]

Do we still need to run DO_CREATE_MESH if we're using KAMP?

[bassamanator]

Well the instructions are for the initial setup, so no, this step cannot be skipped. Moreover, if kamp is disabled, and you don't have a default mesh, print_start will crash. There are instructions on how to disable loading a default mesh, search for NOTE in print_start.

I pushed KAMP to master last night, instructions on how to enable still not included in the readme. Here's how to enable (KAMP is disabled by default).

##### How do I enable KAMP (Klipper Adaptive Meshing & Purging)?

Although this repo contains all the code from the KAMP repository, only the `mesh` functionality of KAMP has been enabled and tested.

Adjust according to your needs.

| File     | `cfgs/misc-macros.cfg`   |
| -------- | ------------------------ |
| Section  | `[gcode_macro _globals]` |
| Variable | `variable_kamp_enable`   |
| Disable  | `0`                      |
| Enable   | `1`                      |

[bassamanator]

Also wanted to mention, if kamp is enabled, the default mesh isn't loaded.