init.g2.rc

import init.g2.usb.rc

on early-init
    mount debugfs debugfs /sys/kernel/debug
    write /sys/class/leds/lcd-backlight/brightness 150

on init
    chmod 0701 /mnt/media_rw
    mkdir /mnt/media_rw/usb 0775 system system
    # See storage config details at http://source.android.com/tech/storage/
    mkdir /mnt/shell/emulated 0700 shell shell
    mkdir /storage/emulated 0555 root root

    # Set permissions for persist partition
    mkdir /persist 0771 system system
    mkdir /firmware 0771 system system
    mkdir /storage/usb 0000 system system
    mkdir /factory 0775 system system
    mkdir /persist-lg 0755 system system
    mkdir /mpt 0755 system system

    export EXTERNAL_STORAGE /storage/emulated/legacy
    export EMULATED_STORAGE_SOURCE /mnt/shell/emulated
    export EMULATED_STORAGE_TARGET /storage/emulated

    # Support legacy paths
    symlink /storage/emulated/legacy /sdcard
    symlink /storage/emulated/legacy /mnt/sdcard
    symlink /storage/emulated/legacy /storage/sdcard0
    symlink /mnt/shell/emulated/0 /storage/emulated/legacy

    # Setup custom emergency number list based on
    # the MCC. This is needed by RIL.
    setprop persist.radio.custom_ecc "1"
    setprop persist.radio.custom_ecc_mcc "{234,235,424,426,427,430,431:999},{334:060,066},{422:9999},{730:133}"
    setprop persist.radio.custom_ecc_mcc_ex "{450:111,112,113,119,122,125,127},{724:190},{440,441:110,118,119,112,911}"
    setprop persist.radio.custom_ecc_voice "{515:117},{452:113,114,115}"
    setprop persist.radio.custom_ecc_hard "911,*911,#911,112,999,000,08,118,120,122,110,119,995,111,113,125,127,133"

    mkdir /sns 0775 system system
    mkdir /sns/cal 0771 system system

on fs
    mount_all ./fstab.g2
    write /sys/kernel/boot_adsp/boot 1
    setprop ro.crypto.fuse_sdcard true

on early-boot
    # set RLIMIT_MEMLOCK to 64MB
    setrlimit 8 67108864 67108864

on boot
    #Create QMUX deamon socket area
    mkdir /dev/socket/qmux_radio 0770 radio radio
    chmod 2770 /dev/socket/qmux_radio
    mkdir /dev/socket/qmux_audio 0770 media audio
    chmod 2770 /dev/socket/qmux_audio
    mkdir /dev/socket/qmux_bluetooth 0770 bluetooth bluetooth
    chmod 2770 /dev/socket/qmux_bluetooth
    mkdir /dev/socket/qmux_gps 0770 gps gps
    chmod 2770 /dev/socket/qmux_gps

    # Allow QMUX daemon to assign port open wait time
    chown radio radio /sys/devices/virtual/hsicctl/hsicctl0/modem_wait

    #Remove SUID bit for iproute2 ip tool
    chmod 0755 /system/bin/ip

    #port-bridge
    chmod 0660 /dev/smd0
    chown system system /dev/smd0

    chmod 0444 /sys/devices/platform/msm_hsusb/gadget/usb_state

    # create symlink for fb1 as HDMI
    symlink /dev/graphics/fb1 /dev/graphics/hdmi

    # Remove write permissions to video related nodes
    chmod 0664 /sys/devices/virtual/graphics/fb1/hpd
    chmod 0664 /sys/devices/virtual/graphics/fb1/video_mode
    chmod 0664 /sys/devices/virtual/graphics/fb1/format_3d

    # Change owner and group for media server and surface flinger
    chown system system /sys/devices/virtual/graphics/fb1/format_3d
    chown system system /sys/devices/virtual/graphics/fb1/hpd

    #For bridgemgr daemon to inform the USB driver of the correct transport
    chown radio radio /sys/class/android_usb/f_rmnet_smd_sdio/transport

    chmod 660 /dev/rtc0
    chown system system /dev/rtc0

    chown root system /proc/net/ip_conntrack

    # Enable DEBUG_SUSPEND, DEBUG_EXIT_SUSPEND, and DEBUG_WAKEUP
    write /sys/module/wakelock/parameters/debug_mask 7

    #To allow interfaces to get v6 address when tethering is enabled
    write /proc/sys/net/ipv6/conf/rmnet0/accept_ra 2
    write /proc/sys/net/ipv6/conf/rmnet1/accept_ra 2
    write /proc/sys/net/ipv6/conf/rmnet2/accept_ra 2
    write /proc/sys/net/ipv6/conf/rmnet3/accept_ra 2
    write /proc/sys/net/ipv6/conf/rmnet4/accept_ra 2
    write /proc/sys/net/ipv6/conf/rmnet5/accept_ra 2
    write /proc/sys/net/ipv6/conf/rmnet6/accept_ra 2
    write /proc/sys/net/ipv6/conf/rmnet7/accept_ra 2
    write /proc/sys/net/ipv6/conf/rmnet_sdio0/accept_ra 2
    write /proc/sys/net/ipv6/conf/rmnet_sdio1/accept_ra 2
    write /proc/sys/net/ipv6/conf/rmnet_sdio2/accept_ra 2
    write /proc/sys/net/ipv6/conf/rmnet_sdio3/accept_ra 2
    write /proc/sys/net/ipv6/conf/rmnet_sdio4/accept_ra 2
    write /proc/sys/net/ipv6/conf/rmnet_sdio5/accept_ra 2
    write /proc/sys/net/ipv6/conf/rmnet_sdio6/accept_ra 2
    write /proc/sys/net/ipv6/conf/rmnet_sdio7/accept_ra 2


# NFC: create data/nfc for nv storage
    mkdir /data/nfc 770 nfc nfc
    mkdir /data/nfc/param 770 nfc nfc

# Assign TCP buffer thresholds to be ceiling value of technology maximums
# Increased technology maximums should be reflected here.
    write /proc/sys/net/core/rmem_max  1220608
    write /proc/sys/net/core/wmem_max  1220608

on boot
    chown bluetooth bluetooth /sys/class/rfkill/rfkill0/type
    chown bluetooth bluetooth /sys/class/rfkill/rfkill0/state
    chmod 0660 /sys/class/rfkill/rfkill0/state
    chmod 0644 /proc/bluetooth/sleep/lpm
    chmod 0644 /proc/bluetooth/sleep/btwrite
    chown bluetooth bluetooth /proc/bluetooth/sleep/lpm
    chown bluetooth bluetooth /proc/bluetooth/sleep/btwrite
    restorecon /proc/bluetooth/sleep/lpm
    restorecon /proc/bluetooth/sleep/btwrite

# lights perms
    chown system system /sys/class/leds/red/brightness
    chown system system /sys/class/leds/green/brightness
    chown system system /sys/class/leds/blue/brightness
    chown system system /sys/class/g2_rgb_led/use_patterns/blink_patterns
    chown system system /sys/class/leds/button-backlight1/brightness
    chown system system /sys/class/leds/button-backlight2/brightness

    chown system wifi /sys/module/bcmdhd/parameters/firmware_path
    chmod 0640 /sys/module/bcmdhd/parameters/firmware_path

# msm specific files that need to be created on /data
on post-fs-data
    mkdir /data/media 0770 media_rw media_rw

    # Create the directories used by the Wireless subsystem
    mkdir /data/misc/wifi 0770 wifi wifi
    mkdir /data/misc/wifi/sockets 0770 wifi wifi
    mkdir /data/misc/wifi/wpa_supplicant 0770 wifi wifi
    mkdir /data/misc/dhcp 0770 dhcp dhcp
# to observe dnsmasq.leases file for dhcp information of soft ap.
    chown dhcp system /data/misc/dhcp

    mkdir /data/misc/playready
    restorecon /data/misc/playready
    mkdir /data/misc/tzapps
    restorecon /data/misc/tzapps

    # Create directory used by audio subsystem
    mkdir /data/misc/audio 0770 audio audio

    # Make sure the default firmware is loaded
    write /sys/module/bcmdhd/parameters/firmware_path "/system/etc/firmware/fw_bcmdhd.bin"

    # Mounting of persist is moved to 'on emmc-fs' and 'on fs' sections
    # We chown/chmod /persist again so because mount is run as root + defaults
    chown system system /persist
    chmod 0664 /sys/devices/platform/msm_sdcc.1/polling
    chmod 0664 /sys/devices/platform/msm_sdcc.2/polling
    chmod 0664 /sys/devices/platform/msm_sdcc.3/polling
    chmod 0664 /sys/devices/platform/msm_sdcc.4/polling

    # Chown polling nodes as needed from UI running on system server
    chown system system /sys/devices/platform/msm_sdcc.1/polling
    chown system system /sys/devices/platform/msm_sdcc.2/polling
    chown system system /sys/devices/platform/msm_sdcc.3/polling
    chown system system /sys/devices/platform/msm_sdcc.4/polling

    #Create the symlink to qcn wpa_supplicant folder for ar6000 wpa_supplicant
    mkdir /data/system 0775 system system
    #symlink /data/misc/wifi/wpa_supplicant /data/system/wpa_supplicant

    #Create directory used by sensor subsystem(dsps)
    mkdir /data/system/sensors
    chmod 665 /data/system/sensors
    write /data/system/sensors/settings 1
    restorecon /data/system/sensors/settings
    chmod 660 /data/system/sensors/settings

    # AKM setting data
    mkdir /data/misc/sensors
    chmod 775 /data/misc/sensors

    mkdir /persist/sensors
    chmod 775 /persist/sensors

    #Provide the access to hostapd.conf only to root and group
    chmod 0660 /data/hostapd/hostapd.conf

    # Enable the setgid bit on the directory
    mkdir /data/audio 0770 media audio
    chmod 2770 /data/audio

    setprop vold.post_fs_data_done 1

    rm /data/local/tmp/adreno_config.txt

    # communicate with mpdecision and thermald
    mkdir /dev/socket/mpdecision 0770 system system
    chmod 2770 /dev/socket/mpdecision

    # time_daemon storage
    mkdir /data/time/ 0700 system system

    # Enable Power modes and set the CPU Freq Sampling rates
    write /sys/module/lpm_resources/enable_low_power/l2 2
    write /sys/module/lpm_resources/enable_low_power/pxo 1
    write /sys/module/lpm_resources/enable_low_power/vdd_dig 1
    write /sys/module/lpm_resources/enable_low_power/vdd_mem 1
    write /sys/module/msm_pm/modes/cpu0/power_collapse/suspend_enabled 1
    write /sys/module/msm_pm/modes/cpu1/power_collapse/suspend_enabled 1
    write /sys/module/msm_pm/modes/cpu2/power_collapse/suspend_enabled 1
    write /sys/module/msm_pm/modes/cpu3/power_collapse/suspend_enabled 1
    write /sys/module/msm_pm/modes/cpu0/power_collapse/idle_enabled 1
    # From the original setup scriptage, revisions != 1.0 disable retention...
    write /sys/module/msm_pm/modes/cpu0/retention/idle_enabled 0
    write /sys/module/msm_pm/modes/cpu1/retention/idle_enabled 0
    write /sys/module/msm_pm/modes/cpu2/retention/idle_enabled 0
    write /sys/module/msm_pm/modes/cpu3/retention/idle_enabled 0
    write /sys/module/msm_thermal/core_control/enabled 0
    write /sys/devices/system/cpu/cpu1/online 1
    write /sys/devices/system/cpu/cpu2/online 1
    write /sys/devices/system/cpu/cpu3/online 1
    write /sys/devices/system/cpu/cpu0/cpufreq/scaling_governor "ondemand"
    write /sys/devices/system/cpu/cpu1/cpufreq/scaling_governor "ondemand"
    write /sys/devices/system/cpu/cpu2/cpufreq/scaling_governor "ondemand"
    write /sys/devices/system/cpu/cpu3/cpufreq/scaling_governor "ondemand"
    write /sys/devices/system/cpu/cpufreq/ondemand/sampling_rate 50000
    write /sys/devices/system/cpu/cpufreq/ondemand/up_threshold 90
    write /sys/devices/system/cpu/cpufreq/ondemand/io_is_busy 1
    write /sys/devices/system/cpu/cpufreq/ondemand/sampling_down_factor 2
    write /sys/devices/system/cpu/cpufreq/ondemand/down_differential 10
    write /sys/devices/system/cpu/cpufreq/ondemand/up_threshold_multi_core 70
    write /sys/devices/system/cpu/cpufreq/ondemand/down_differential_multi_core 3
    write /sys/devices/system/cpu/cpufreq/ondemand/optimal_freq 960000
    write /sys/devices/system/cpu/cpufreq/ondemand/sync_freq 960000
    write /sys/devices/system/cpu/cpufreq/ondemand/up_threshold_any_cpu_load 80
    write /sys/devices/system/cpu/cpu0/cpufreq/scaling_min_freq 300000
    write /sys/devices/system/cpu/cpu1/cpufreq/scaling_min_freq 300000
    write /sys/devices/system/cpu/cpu2/cpufreq/scaling_min_freq 300000
    write /sys/devices/system/cpu/cpu3/cpufreq/scaling_min_freq 300000
    write /sys/devices/system/cpu/cpufreq/ondemand/middle_grid_step 7
    write /sys/devices/system/cpu/cpufreq/ondemand/middle_grid_load 40
    write /sys/devices/system/cpu/cpufreq/ondemand/high_grid_step 14
    write /sys/devices/system/cpu/cpufreq/ondemand/high_grid_load 50
    chown root system /sys/devices/system/cpu/mfreq
    chmod 0220 /sys/devices/system/cpu/mfreq
    write /sys/module/msm_thermal/core_control/enabled 1
    write /dev/cpuctl/apps/cpu.notify_on_migrate 1

    # Torch
    chown system camera /sys/class/leds/led:flash_torch/brightness
    chmod 0660 /sys/class/leds/led:flash_torch/brightness

    chown system system /sys/devices/virtual/input/lge_touch/touch_gesture
    chown root system /sys/devices/platform/tspdrv/nforce_timed
    chown root system /sys/devices/platform/kcal_ctrl.0/kcal
    chown root system /sys/devices/platform/kcal_ctrl.0/kcal_ctrl
    chmod 0664 /sys/devices/platform/tspdrv/nforce_timed
    chmod 0664 /sys/devices/platform/kcal_ctrl.0/kcal
    chmod 0664 /sys/devices/platform/kcal_ctrl.0/kcal_ctrl
    restorecon /sys/devices/platform/tspdrv/nforce_timed
    restorecon /sys/devices/platform/kcal_ctrl.0/kcal
    restorecon /sys/devices/platform/kcal_ctrl.0/kcal_ctrl

on charger
    # Enable Power modes and set the CPU Freq Sampling rates
    write /sys/module/lpm_resources/enable_low_power/l2 2
    write /sys/module/lpm_resources/enable_low_power/pxo 1
    write /sys/module/lpm_resources/enable_low_power/vdd_dig 1
    write /sys/module/lpm_resources/enable_low_power/vdd_mem 1
    write /sys/module/msm_pm/modes/cpu0/power_collapse/suspend_enabled 1
    write /sys/module/msm_pm/modes/cpu1/power_collapse/suspend_enabled 1
    write /sys/module/msm_pm/modes/cpu2/power_collapse/suspend_enabled 1
    write /sys/module/msm_pm/modes/cpu3/power_collapse/suspend_enabled 1
    write /sys/devices/system/cpu/cpu0/cpufreq/scaling_governor "powersave"
    write /sys/devices/system/cpu/cpu1/cpufreq/scaling_governor "powersave"
    write /sys/devices/system/cpu/cpu2/cpufreq/scaling_governor "powersave"
    write /sys/devices/system/cpu/cpu3/cpufreq/scaling_governor "powersave"
    write /sys/devices/system/cpu/cpu1/online 0
    write /sys/devices/system/cpu/cpu2/online 0
    write /sys/devices/system/cpu/cpu3/online 0
    start rmt_storage

on property:init.svc.wpa_supplicant=stopped
    stop dhcpcd

service rmt_storage /system/bin/rmt_storage
    class core
    user root

service bridgemgrd /system/bin/bridgemgrd
    class main
    user radio
    group radio

# QMUX must be in multiple groups to support external process connections
service qmuxd /system/bin/qmuxd
    class main
    user radio
    group radio audio bluetooth gps qcom_diag

service netmgrd /system/bin/netmgrd
    class main

service sensors /system/bin/sensors.qcom
    class main
    user root
    group root

service dhcpcd_wlan0 /system/bin/dhcpcd -aABDKL
    class main
    disabled
    oneshot

service dhcpcd_p2p /system/bin/dhcpcd -aABKL
    class main
    disabled
    oneshot

service iprenew_wlan0 /system/bin/dhcpcd -n
    class main
    disabled
    oneshot

service iprenew_p2p /system/bin/dhcpcd -n
    class main
    disabled
    oneshot

service dhcpcd_bt-pan /system/bin/dhcpcd -BKLG
    disabled
    oneshot

service iprenew_bt-pan /system/bin/dhcpcd -n
    disabled
    oneshot

on property:ro.data.large_tcp_window_size=true
    # Adjust socket buffer to enlarge TCP receive window for high bandwidth (e.g. DO-RevB)
    write /proc/sys/net/ipv4/tcp_adv_win_scale 2

service charger /charger
    class charger

# virtual sdcard daemon running as media_rw (1023)
service sdcard /system/bin/sdcard /data/media /mnt/shell/emulated 1023 1023
    class late_start

service mpdecision /system/bin/mpdecision --no_sleep --avg_comp
    class main

service qcamerasvr /system/bin/mm-qcamera-daemon
    class late_start
    user camera
    group camera system inet input

#start GNSS/Sensor interface daemon
service gsiff_daemon /system/bin/gsiff_daemon
    class late_start
    user gps
    group gps net_raw misc

service qseecomd /system/bin/qseecomd
    class late_start
    user root
    group root

service cnd /system/bin/cnd
    class late_start
    socket cnd stream 660 root inet

service thermal-engine /system/bin/thermal-engine
   class main
   user root
   group root

service irsc_util /system/bin/logwrapper /system/bin/irsc_util "/etc/sec_config"
    class main
    user root
    oneshot

service p2p_supplicant /system/bin/logwrapper /system/bin/wpa_supplicant \
    -iwlan0 -Dnl80211 -c/data/misc/wifi/wpa_supplicant.conf \
    -I/system/etc/wifi/wpa_supplicant_overlay.conf \
    -O/data/misc/wifi/sockets -N \
    -ip2p0 -Dnl80211 -c/data/misc/wifi/p2p_supplicant.conf \
    -I/system/etc/wifi/p2p_supplicant_overlay.conf \
    -puse_p2p_group_interface=1 -e/data/misc/wifi/entropy.bin \
    -g@android:wpa_wlan0
    #   we will start as root and wpa_supplicant will switch to user wifi
    #   after setting up the capabilities required for WEXT
    #   user wifi
    #   group wifi inet keystore
    class main
    socket wpa_wlan0 dgram 660 wifi wifi
    disabled
    oneshot

service wpa_supplicant /system/bin/logwrapper /system/bin/wpa_supplicant \
    -iwlan0 -Dnl80211 -c/data/misc/wifi/wpa_supplicant.conf \
    -I/system/etc/wifi/wpa_supplicant_overlay.conf \
    -O/data/misc/wifi/sockets \
    -e/data/misc/wifi/entropy.bin -g@android:wpa_wlan0
    #   we will start as root and wpa_supplicant will switch to user wifi
    #   after setting up the capabilities required for WEXT
    #   user wifi
    #   group wifi inet keystore
    class main
    socket wpa_wlan0 dgram 660 wifi wifi
    disabled
    oneshot

service conn_init /system/bin/logwrapper /system/bin/hwaddrs
    class late_start
    user system
    group system wifi
    oneshot

# Running hwaddrs under init is enforcing 0600, we need more
on property:init.svc.conn_init=stopped
    chmod 644 /data/misc/wifi/config
    chmod 644 /data/misc/bdaddr

service time_daemon /system/bin/time_daemon
    class late_start
    user root
    group root

service fuse_usb /system/bin/sdcard -u 1023 -g 1023 /mnt/media_rw/usb /storage/usb
    class late_start
    disabled

## Power profiles (CM QS tile)
## restarting thermal-engine will kill the system :/

# Powersave
on property:sys.perf.profile=0
    start mpdecision
    #start thermal-engine
    write /sys/devices/system/cpu/cpu0/cpufreq/scaling_governor conservative
    write /sys/devices/system/cpu/cpu1/cpufreq/scaling_governor conservative
    write /sys/devices/system/cpu/cpu2/cpufreq/scaling_governor conservative
    write /sys/devices/system/cpu/cpu3/cpufreq/scaling_governor conservative

# Balanced
on property:sys.perf.profile=1
    start mpdecision
    #start thermal-engine
    write /sys/devices/system/cpu/cpu0/cpufreq/scaling_governor ondemand
    write /sys/devices/system/cpu/cpu1/cpufreq/scaling_governor ondemand
    write /sys/devices/system/cpu/cpu2/cpufreq/scaling_governor ondemand
    write /sys/devices/system/cpu/cpu3/cpufreq/scaling_governor ondemand

# High performance
on property:sys.perf.profile=2
    stop mpdecision
    #stop thermal-engine
    write /sys/devices/system/cpu/cpu0/online 1
    write /sys/devices/system/cpu/cpu1/online 1
    write /sys/devices/system/cpu/cpu2/online 1
    write /sys/devices/system/cpu/cpu3/online 1
    write /sys/devices/system/cpu/cpu0/cpufreq/scaling_governor performance
    write /sys/devices/system/cpu/cpu1/cpufreq/scaling_governor performance
    write /sys/devices/system/cpu/cpu2/cpufreq/scaling_governor performance
    write /sys/devices/system/cpu/cpu3/cpufreq/scaling_governor performance