-
Notifications
You must be signed in to change notification settings - Fork 271
/
ili9486.cpp
163 lines (141 loc) · 6.54 KB
/
ili9486.cpp
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
#include "config.h"
#if defined(ILI9486) || defined(ILI9486L)
#include "spi.h"
#include <memory.h>
#include <stdio.h>
void InitILI9486()
{
// If a Reset pin is defined, toggle it briefly high->low->high to enable the device. Some devices do not have a reset pin, in which case compile with GPIO_TFT_RESET_PIN left undefined.
#if defined(GPIO_TFT_RESET_PIN) && GPIO_TFT_RESET_PIN >= 0
printf("Resetting display at reset GPIO pin %d\n", GPIO_TFT_RESET_PIN);
SET_GPIO_MODE(GPIO_TFT_RESET_PIN, 1);
SET_GPIO(GPIO_TFT_RESET_PIN);
usleep(120 * 1000);
CLEAR_GPIO(GPIO_TFT_RESET_PIN);
usleep(120 * 1000);
SET_GPIO(GPIO_TFT_RESET_PIN);
usleep(120 * 1000);
#endif
// Do the initialization with a very low SPI bus speed, so that it will succeed even if the bus speed chosen by the user is too high.
spi->clk = 34;
__sync_synchronize();
BEGIN_SPI_COMMUNICATION();
{
#ifdef DISPLAY_SPI_BUS_IS_16BITS_WIDE
SPI_TRANSFER(0xB0/*Interface Mode Control*/, 0x00, 0x00/*DE polarity=High enable, PCKL polarity=data fetched at rising time, HSYNC polarity=Low level sync clock, VSYNC polarity=Low level sync clock*/);
#else
SPI_TRANSFER(0xB0/*Interface Mode Control*/, 0x00/*DE polarity=High enable, PCKL polarity=data fetched at rising time, HSYNC polarity=Low level sync clock, VSYNC polarity=Low level sync clock*/);
#endif
SPI_TRANSFER(0x11/*Sleep OUT*/);
usleep(120*1000);
#ifdef DISPLAY_COLOR_FORMAT_R6X2G6X2B6X2
const uint8_t pixelFormat = 0x66; /*DPI(RGB Interface)=18bits/pixel, DBI(CPU Interface)=18bits/pixel*/
#else
const uint8_t pixelFormat = 0x55; /*DPI(RGB Interface)=16bits/pixel, DBI(CPU Interface)=16bits/pixel*/
#endif
#ifdef DISPLAY_SPI_BUS_IS_16BITS_WIDE
SPI_TRANSFER(0x3A/*Interface Pixel Format*/, 0x00, pixelFormat);
#else
SPI_TRANSFER(0x3A/*Interface Pixel Format*/, pixelFormat);
#endif
// Oddly, WaveShare 3.5" (B) seems to need Display Inversion ON, whereas WaveShare 3.5" (A) seems to need Display Inversion OFF for proper image. See https://github.com/juj/fbcp-ili9341/issues/8
#ifdef DISPLAY_INVERT_COLORS
SPI_TRANSFER(0x21/*Display Inversion ON*/);
#else
SPI_TRANSFER(0x20/*Display Inversion OFF*/);
#endif
#ifdef DISPLAY_SPI_BUS_IS_16BITS_WIDE
SPI_TRANSFER(0xC0/*Power Control 1*/, 0x00, 0x09, 0x00, 0x09);
SPI_TRANSFER(0xC1/*Power Control 2*/, 0x00, 0x41, 0x00, 0x00);
SPI_TRANSFER(0xC2/*Power Control 3*/, 0x00, 0x33);
SPI_TRANSFER(0xC5/*VCOM Control*/, 0x00, 0x00, 0x00, 0x36);
#else
SPI_TRANSFER(0xC0/*Power Control 1*/, 0x09, 0x09);
SPI_TRANSFER(0xC1/*Power Control 2*/, 0x41, 0x00);
SPI_TRANSFER(0xC2/*Power Control 3*/, 0x33);
SPI_TRANSFER(0xC5/*VCOM Control*/, 0x00, 0x36);
#endif
#define MADCTL_BGR_PIXEL_ORDER (1<<3)
#define MADCTL_ROW_COLUMN_EXCHANGE (1<<5)
#define MADCTL_COLUMN_ADDRESS_ORDER_SWAP (1<<6)
#define MADCTL_ROW_ADDRESS_ORDER_SWAP (1<<7)
#define MADCTL_ROTATE_180_DEGREES (MADCTL_COLUMN_ADDRESS_ORDER_SWAP | MADCTL_ROW_ADDRESS_ORDER_SWAP)
uint8_t madctl = 0;
#ifndef DISPLAY_SWAP_BGR
madctl |= MADCTL_BGR_PIXEL_ORDER;
#endif
#if defined(DISPLAY_FLIP_ORIENTATION_IN_HARDWARE)
madctl |= MADCTL_ROW_COLUMN_EXCHANGE;
#endif
#ifdef DISPLAY_ROTATE_180_DEGREES
madctl ^= MADCTL_ROTATE_180_DEGREES;
#endif
#ifdef DISPLAY_SPI_BUS_IS_16BITS_WIDE
SPI_TRANSFER(0x36/*MADCTL: Memory Access Control*/, 0x00, madctl);
#ifndef WAVESHARE_SKIP_GAMMA_CONTROL
SPI_TRANSFER(0xE0/*Positive Gamma Control*/, 0x00, 0x00, 0x00, 0x2C, 0x00, 0x2C, 0x00, 0x0B, 0x00, 0x0C, 0x00, 0x04, 0x00, 0x4C, 0x00, 0x64, 0x00, 0x36, 0x00, 0x03, 0x00, 0x0E, 0x00, 0x01, 0x00, 0x10, 0x00, 0x01, 0x00, 0x00);
SPI_TRANSFER(0xE1/*Negative Gamma Control*/, 0x00, 0x0F, 0x00, 0x37, 0x00, 0x37, 0x00, 0x0C, 0x00, 0x0F, 0x00, 0x05, 0x00, 0x50, 0x00, 0x32, 0x00, 0x36, 0x00, 0x04, 0x00, 0x0B, 0x00, 0x00, 0x00, 0x19, 0x00, 0x14, 0x00, 0x0F);
#endif
SPI_TRANSFER(0xB6/*Display Function Control*/, 0, 0, 0, /*ISC=2*/2, 0, /*Display Height h=*/59); // Actual display height = (h+1)*8 so (59+1)*8=480
#else
SPI_TRANSFER(0x36/*MADCTL: Memory Access Control*/, madctl);
#ifndef WAVESHARE_SKIP_GAMMA_CONTROL
SPI_TRANSFER(0xE0/*Positive Gamma Control*/, 0x00, 0x2C, 0x2C, 0x0B, 0x0C, 0x04, 0x4C, 0x64, 0x36, 0x03, 0x0E, 0x01, 0x10, 0x01, 0x00);
SPI_TRANSFER(0xE1/*Negative Gamma Control*/, 0x0F, 0x37, 0x37, 0x0C, 0x0F, 0x05, 0x50, 0x32, 0x36, 0x04, 0x0B, 0x00, 0x19, 0x14, 0x0F);
#endif
SPI_TRANSFER(0xB6/*Display Function Control*/, 0, /*ISC=2*/2, /*Display Height h=*/59); // Actual display height = (h+1)*8 so (59+1)*8=480
#endif
SPI_TRANSFER(0x11/*Sleep OUT*/);
usleep(120*1000);
SPI_TRANSFER(0x29/*Display ON*/);
SPI_TRANSFER(0x38/*Idle Mode OFF*/);
SPI_TRANSFER(0x13/*Normal Display Mode ON*/);
#if defined(GPIO_TFT_BACKLIGHT) && defined(BACKLIGHT_CONTROL)
printf("Setting TFT backlight on at pin %d\n", GPIO_TFT_BACKLIGHT);
TurnBacklightOn();
#endif
ClearScreen();
}
#ifndef USE_DMA_TRANSFERS // For DMA transfers, keep SPI CS & TA active.
END_SPI_COMMUNICATION();
#endif
// And speed up to the desired operation speed finally after init is done.
usleep(10 * 1000); // Delay a bit before restoring CLK, or otherwise this has been observed to cause the display not init if done back to back after the clear operation above.
spi->clk = SPI_BUS_CLOCK_DIVISOR;
}
void TurnBacklightOff()
{
#if defined(GPIO_TFT_BACKLIGHT) && defined(BACKLIGHT_CONTROL)
SET_GPIO_MODE(GPIO_TFT_BACKLIGHT, 0x01); // Set backlight pin to digital 0/1 output mode (0x01) in case it had been PWM controlled
CLEAR_GPIO(GPIO_TFT_BACKLIGHT); // And turn the backlight off.
#endif
}
void TurnBacklightOn()
{
#if defined(GPIO_TFT_BACKLIGHT) && defined(BACKLIGHT_CONTROL)
SET_GPIO_MODE(GPIO_TFT_BACKLIGHT, 0x01); // Set backlight pin to digital 0/1 output mode (0x01) in case it had been PWM controlled
SET_GPIO(GPIO_TFT_BACKLIGHT); // And turn the backlight on.
#endif
}
void TurnDisplayOff()
{
TurnBacklightOff();
QUEUE_SPI_TRANSFER(0x28/*Display OFF*/);
QUEUE_SPI_TRANSFER(0x10/*Enter Sleep Mode*/);
usleep(120*1000); // Sleep off can be sent 120msecs after entering sleep mode the earliest, so synchronously sleep here for that duration to be safe.
}
void TurnDisplayOn()
{
TurnBacklightOff();
QUEUE_SPI_TRANSFER(0x11/*Sleep Out*/);
usleep(120 * 1000);
QUEUE_SPI_TRANSFER(0x29/*Display ON*/);
usleep(120 * 1000);
TurnBacklightOn();
}
void DeinitSPIDisplay()
{
ClearScreen();
TurnDisplayOff();
}
#endif