Disclaimer: This project combines a lot of toolchain and binary knowledge and experience I collected and gained in recent years about legacy x86_64 boot. The main contribution IMHO is how the binary is assembled and that the thing boots with all the properties described below, but not the high-level functionality itself.
I am especially proud of the well-commented structure of the assembly files. For example the whole page-table mappings are done IMHO very nicely even though it is assembly language. Also, I think it turned out quite cool how I configured the linker script. I hope this can be a learning resource for others!
Further: This project is a solution for a niche use-case, especially in 2024.
PhipsBoot is a relocatable x86_64 bootloader written in Rust and assembly that loads a kernel into 64-bit mode. It abstracts a lot of boot-related x86_64 complexity away.
The main advantage of PhipsBoot is seen when loaded by GRUB via Multiboot2 in legacy BIOS boot systems, where it can be relocated in physical memory even though the kernel binary is a static ELF. However, PhipsBoot also supports Multiboot1 and XEN PVH entries.
PhipsBoot expects an 32-bit protected mode without paging machine state at is entry. This corresponds to the Multiboot2 i386 machine state definition.
| Firmware | Hand-Off by | Status | Comment |
|---|---|---|---|
| BIOS/UEFI | Firmware | ❌ | Use existing projects as chainloader. |
| BIOS/UEFI | Multiboot 1/2 | ✅ | Recommended (BIOS + GRUB + Multiboot 2) |
| * | Xen PVH | ✅ |
Effectively, in the open-source world you are limited to GRUB when you want to boot your custom kernel on legacy BIOS x86_64 systems, while keeping up a certain level of user and developer experience. By reusing all the abstracted away complexity that GRUB comes with, PhipsBoot can be much simpler and easier to program, install, adopt, and use.
It solves several problems every 64-bit kernel has to perform anyway, such as performing the transition into 64-bit long mode while also being relocatable in physical memory to never clash with firmware code, MMIO regions or otherwise reserved addresses. Kernels using this bootloader can massively simplify their build setup and boot code as much complexity is outsourced to PhipsBoot, such as several CPU state transitions and intermediate identity page mappings.
By far the biggest contribution of PhipsBoot is that it is relocatable in physical memory when it is loaded by GRUB. Here, you can read more of the overall challenges.
First of all: If you are targeting UEFI and only UEFI, you need none of this! The world is much simpler there. However, for legacy BIOS, the bootloader developer and user experience is just difficult. To not be forced to use GRUB, one can also write an entire bootloader supporting legacy BIOS boot in Rust. That's awesome! However, installing legacy BIOS stage 1 bootloaders on disk is much more complicated, as one has to patch the MBR instead of just putting a file on disk. By using GRUB however, it is relatively easy to put PhipsBoot or other Multiboot payloads on disk and reference them from the GRUB config.
If you are targeting legacy x86 boot and have the freedom to choose and install your own stage 1 bootloader, you can also have a look at Limine, which is superior to GRUB and production ready. It also brings your kernel into 64-bit mode right away, making PhipsBoot obsolete.
I'm kind of proud of the way I set up page-tables from assembly using descriptive GNU as macros! I didn't see anything like that so far. IMHO it is a great approach as low-level programming and assembly doesn't necessarily has to be ugly. 🤓
- General description about the architecture: ARCHITECTURE.md
- Build and run test:
$ make && make integration-test
Artifacts are in ./build.
You have multiple options, for example:
$ cloud-hypervisor --debug-console file=log.txt --kernel ./build/phipsboot.elf64(using Xen PVH)$ qemu-system-x86_64 -kernel ./build/phipsboot.elf32 -debugcon stdio(using Multiboot 1)
Supported payloads that PhipsBoot can boot are ELF executables (static and dyn). The hand-off to the kernel follows the PhipsBoot protocol.
This protocol describes the hardware state and the handover to your kernel when it is booted by PhipsBoot.
The kernel entry is taken from the ELF entry. It is invoked using the SystemV x86_64 calling convention. First argument passed to your kernel is a point to the boot information.
- PhipsBoot is still mapped and occupies (at most) 2 MiB of virtual address space
- BSP in 64-bit long mode with 4-level paging
- APs are still asleep
- control registers
%cr0: PE (0), MP (1), WP (16), PG (31)%cr4: PAE (5), OSFXSR (9), OSXMMEXCPT (10)%cr3: holds the physical address of the root page table
- MSRs
efer: LME (8), NX (11)
- GDT, which is living in the physical address space of PhipsBoot, is set with
two selectors:
- null selector
- (64-bit, code segment, ring 0)-selector
%rspis set to a valid 128 KiB stack%rdihas pointer to boot information- All load segments of the kernel are loaded with their corresponding page-table rights. The NX bits are set for all non-executable LOAD segments.
TODO implement
TODO implement
You can use the following GRUB configuration:
menuentry "Kernel" {
multiboot2 /phipsboot
module2 /your-kernel
boot
}
The build itself produces phipsboot.elf32 and phipsboot.elf64. Both are
identical except for the ELF header. You usually always want to use the .elf64
version except for when booting it via Multiboot1, where compliant bootloaders
only accept 32-bit ELFs.