Here is a diagram showing the connection phase and the network transactions required to turn a sonoff device on.
image::http://alt2.pbeirne.com/images/sonoff_cmnd_flow3.png[flow diagram]
In a typical setup, you'll have multiple devices on the left-hand side.
There are lots of ways to control your devices. One typically uses a laptop/desktop to configure and test your Sonoffs and perhaps a smartphone to keep track of what's happening. In the long run you might want to integrate your device in a home-automation system like node-RED, openHAB, HomeAssistant, HomeBridge, Domoticz, ...
[options="header"]
|===
|Message|Issued by|Intent
|cmnd|devices shown on the right-hand side|control the Sonoff; set configuration; ask for status
|stat|the Sonoffs on the left-hand side|report back status or configuration message
|tele|some Sonoffs (like temperature measuring devices)|report unsolicited telemetry info at periodic intervals
|===
These are prefix1, prefix2 & prefix3 in the code
MQTT settings can be initially setup in the web interface and thereafter configured by commands.
Enable MQTT with the tickbox under Configuration -> Configuration Other
Once enabled MQTT can be configured at Configuration -> Configure MQTT.
[options="header"] |=== |Field|Size|Default(my_user_config.h)|Notes |Host name |32|MQTT_HOST=mqtt_broker.com|Remote URL or ip address. Note that without a special firmware build SSL is NOT supported. |Port|uint|MQTT_PORT=1883|0-65535 |Client Id|32|MQTT_CLIENT_ID=DVES_%06X|FallBack topic of this device, will be unique for every device; logged by the MQTT server |Username|32|MQTT_USER=DVES_USER|Username for MQTT server authentication |Password|32|MQTT_PASS=DVES_PASS|Password for MQTT server authentication |Topic|32|MQTT_TOPIC=sonoff|User friendly topic name; usually describes the location or use of this device; used in the MQTT commands and responses; should be unique |Full Topic|100|%prefix%/%topic%|Format string used to assemble the MQTT commands |===
Note: By default firmware will search for an MQTT broker using mDNS by searching for a tcp record mqtt.local. However the use of local mDNS hostnames (ex: mqtt_home.local) is not supported, if you want to use a broker on your local network you need to use its local IP or rely on a local DNS to resolve the hostnames.
mosquitto_sub -h mqtt_server_name.com -t stat/my_sonoff/POWER -v # listen for status
mosquitto_pub -h mqtt_server_name.com -t cmnd/my_sonoff/power -m 1 # turn on the light
See the wiki's Commands[command list] for the definitive list of operations that you can perform. The first word in the column marked Command is the text that you need to put at the end of a cmnd string when you issue a publication message. The second word is the contents of the payload. If there is no second word, you can simply send an empty payload. For example:
[options="header"] |=== |Command | Description |Power | Show current power state as On or Off |Power on | Turn power On |Power off | Turn power Off |===
To execute these, issue (publish) these MQTT requests
MQTT topic MQTT payload
cmnd/my_device/power <empty>
cmnd/my_device/power on
cmnd/my_device/power off
The sonoff will respond with these publications:
MQTT topic MQTT payload
stat/my_device/POWER ON
stat/my_device/POWER ON
stat/my_device/POWER OFF
If you have subscribed to these stat messages, you can be informed of changes on the device.
You'll need an MQTT server somewhere to communicate with your Sonoff. Some people use publicly available servers, such as iot.eclipse.org. http://moxd.io/2015/10/public-mqtt-brokers/[List of brokers]
Other people think the MQTT server should reside inside your private LAN. You could use a Raspberry/Orange Pi, or just about any Linux machine as the server/broker; you might even squeeze it into your router if you're using OpenWRT.
The middle word of the 'topic' phrase indicates the name of the device. You can communicate with a sonoff using its topic name, its group name or its FallBack topic name (like DVES_123456).
At the time the sonoff connects with the MQTT server, the sonoff subscribes to +++"cmnd/my-topic/#", "cmnd/group-topic/#" and "cmnd/fallback-topic/#",+++ and listens on all those names. You can find the group name using "status 0" and the FallBack topic using "status 6" or both on the Information page in WebUI.
See these sites:
https://www.digitalocean.com/community/questions/how-to-setup-a-mosquitto-mqtt-server-and-receive-data-from-owntracks[Rufio howto] + http://wingsquare.com/blog/setting-up-mqtt-mosquitto-broker-in-ubuntu-linux/[Wingsquare howto] + http://www.instructables.com/id/Installing-MQTT-BrokerMosquitto-on-Raspberry-Pi/[Instructables howto on Raspberry Pi]
You can install the mosquitto client system using either
[Cygwin] setup mosquitto_client
[Ubuntu/Debian] apt install mosquitto_client
[Centos/Fedora] yum install mosquitto_client
You can control the relay in your Sonoff with mosquitto_pub. Suppose your Sonoff topic is "my_house_living_room" and your mqtt broker is "control_central". To turn on the Sonoff, type this on the command line:
mosquitto_pub -h control_central -t cmnd/my_house_living_room/power -m 1
You can turn the Sonoff back off again with:
mosquitto_pub -h control_central -t cmnd/my_house_living_room/power -m 0
If you want to find out what state your sonoff is, issue this command with an empty payload to trigger a status response (see below for how to listen):
mosquitto_pub -h control_central -t cmnd/my_house_living_room/status -n
To keep track of your sonoff, just subscribe to messages starting with stat, followed by your topic. For example, to pick up status messages from your sonoff, use
mosquitto_sub -h control_central -t stat/my_house_living_room/STATUS -v
The optional -v will show you the topic and payload.
These Sonoffs can provide specific information if you wish. To just monitor the relay state, try
mosquitto_sub -h control_central -t stat/my_house_living_room/POWER
You can also use wildcards in your subscription. To pick up every message from this sonoff, you can use
mosquitto_sub -h control_central -t stat/my_house_living_room/+
and then some other code to just pick out the messages you want. If you have a collection of sonoffs, you can listen to them all by either using the group topic
mosquitto_sub -h control_central -t stat/my_house_collection/POWER
or by using a wildcard in the 2nd position
mosquitto_sub -h control_central -t stat/+/POWER
Of course you can always call system() or subprocess() to run the mosquitto_pub and mosquitto_sub command lines as shown above. But if you wish, you can install the paho-mqtt package and communicate with MQTT using Python objects.
Let's turn the lights on, wait a few seconds, turn them off, check the status and wait for a time stamp
import paho.mqtt.client as mqtt, time, sys
last_topic = ""
last_payload = ""
# main
def on_connect(client, userdata, flags, rc):
print("Connected")
client.is_connected = True
def on_message(client, userdata, message):
''' note: message is a tuple of (topic, payload, qos, retain)'''
global last_topic, last_payload
last_topic = message.topic
last_payload = message.payload
print("Got a message with topic: [" + last_topic + "] and payload [" + last_payload + "]")
client = mqtt.Client()
# if you need a username and/or password for mqtt uncomment next line
# client.username_pw_set("myusr", password="mypwd")
client.on_connect = on_connect
client.on_message = on_message
client.is_connected = False
client.loop_start()
client.connect("control_central") # replace "control_central" with ip address or name of server
time.sleep(6)
if not client.is_connected:
print("problem connecting to the MQTT server; please check your settings")
sys.exit(1)
# edit subscribe and publish lines and use yours like "stat/tasmota/POWER"
client.subscribe("stat/my_house_living_room/POWER")
client.publish("cmnd/my_house_living_room/power","1")
# wait a little bit
time.sleep(15)
client.publish("cmnd/my_house_living_room/power","0")
# ask for system status
time.sleep(1)
client.subscribe("stat/my_house_living_room/STATUS")
client.publish("cmnd/my_house_living_room/status",None)
# now wait for a time stamp from the sonoff; this could take an hour
client.subscribe("tele/my_house_living_room/+")
# if using tasmota-sensors.bin next section will not work unless you replace "STATE" with "SENSOR"
while 1:
if last_topic.startswith("tele/") and last_topic.endswith("STATE"):
locate_time = last_payload.find(b'"Time":')
the_time = last_payload[locate_time+8:locate_time+8+19]
print("the sonoff thinks the time is: "+the_time.decode("utf-8"))
break
time.sleep(5)
client.loop_stop()
client.disconnect()Ref: https://pypi.python.org/pypi/paho-mqtt/1.1[Python MQTT]
Using the node module MQTT.js you can connect to the MQTT broker, send messages and listen to topics. The example uses code compatible with Node v4 or later.
'use strict';
const mqtt = require('mqtt');
const broker = 'mqtt://192.168.0.13'; // MQTT Broker hostname/IP address
const client = mqtt.connect(broker); // MQTT Client
const device = 'switch1'; // Sonoff device identifier
let state = 'OFF';
let timer;
client.on('connect', function () {
console.log(`${Date.now()} Client connected to ${broker}`);
client.subscribe(`stat/${device}/+`);
client.subscribe(`tele/${device}/+`);
client.publish(`cmnd/${device}/status`);
timer = setInterval(loop, 2000);
});
client.on('message', function (topic, message) {
if (topic === `stat/${device}/POWER`) {
state = message.toString();
}
console.log(`${Date.now()} RX ${topic} ${message}`);
});
function loop() {
if (!client.connected) {
return timer && timer.clearInterval();
}
let newState = state === 'OFF' ? 'ON' : 'OFF';
client.publish(`cmnd/${device}/power`, newState);
console.log(`${Date.now()} TX cmnd/${device}/power ${newState}`);
}Ref: https://github.com/mqttjs/MQTT.js[Node MQTT.js]
The https://play.google.com/store/apps/details?id=com.thn.iotmqttdashboard[MQTT Dashboard] provides the ability to connect and control Sonoff devices directly.
On the first page, enter the details of how your phone should connect to the MQTT broker. On the SUBSCRIBE page, you
can create widgets which listen for publications from the Sonoff. A typical subscription for a power controller might be
stat/my_device/POWER
You could also pick up all your devices with
stat/+/POWER
On the PUBLISH page, you can create widgets to toggle or on/off your Sonoff. Typically you'd send a
cmnd/my_device/power as the topic, and on or off as the publish value. Note that you can also have separate words
on the app's user interface, such as illuminated and extinguished; these are not sent out via MQTT, they're just
user interface.
Alternatively, if you're using a home automation system, there may be an Andriod/iOS app to link to your home automation. That's not covered in this how-to.
MQTT: CONNECT FAILED x.x.x.x:x, rc {code}. Retry in 10 seconds
-4: MQTT_CONNECTION_TIMEOUT - the server didn't respond within the keepalive time
-3: MQTT_CONNECTION_LOST - the network connection was broken
-2: MQTT_CONNECT_FAILED - the network connection failed
-1: MQTT_DISCONNECTED - the client is disconnected cleanly
0: MQTT_CONNECTED - the client is connected
1: MQTT_CONNECT_BAD_PROTOCOL - the server doesn't support the requested version of MQTT
2: MQTT_CONNECT_BAD_CLIENT_ID - the server rejected the client identifier
3: MQTT_CONNECT_UNAVAILABLE - the server was unable to accept the connection
4: MQTT_CONNECT_BAD_CREDENTIALS - the username/password were rejected
5: MQTT_CONNECT_UNAUTHORIZED - the client was not authorized to connect
- https://play.google.com/store/apps/details?id=mqttsnooper.mqttsnooper[ MQTT Snooper - Sniffer App on Android]
- https://mqtt-explorer.com/?c=tasmota-wiki[MQTT Explorer - Desktop Application]